SPM3215 no.7265-1/3 features ? single control. ? control voltage : +3 / 0v. ? small package (mcph6). ? low insertion loss (@1ghz). ? high isolation (@1ghz). specifications absolute maximum ratings at ta=25 c parameter symbol conditions ratings unit control voltage v ctl 5.0 v power dissipation p d 150 mw storage temperature tstg - 55 to +150 c operating temperature topr - 20 to +85 c electrical characteristics at ta=25 c control voltage 1, 2 : 0 / +3v rating parameter conditions min typ max unit f=800mhz 0.6 0.9 db in - - out1 f=1.5ghz 0.6 0.9 db f=2ghz 0.7 1.0 db insertion loss f=2.5ghz 0.9 1.2 db f=800mhz 0.7 1.0 db in - - out2 f=1.5ghz 0.8 1.1 db f=2ghz 0.9 1.2 db f=2.5ghz 1.1 1.4 db marking : rg continued on next page. vctl in y out1 in y out2 0 on off +3v off on *v dd =3v ordering number : enn7265 sanyo electric co.,ltd. semiconductor company tokyo office tokyo bldg., 1-10, 1 chome, ueno, taito-ku, tokyo, 110-8534 japan SPM3215 wide-band switch mmic operating with single power supply package dimensions unit : mm 1319 [SPM3215] o1002 ts im ta-100199 any and all sanyo products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. consult with your sanyo representative nearest you before using any sanyo products described or contained herein in such applications. sanyo assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all sanyo products described or contained herein. 1 : ctl 2 : in 3 : tc 4 : out1 5 : gnd 6 : out2 sanyo : mcph6 0.25 0.25 0.07 2.1 1.6 2.0 0.65 0.3 0.85 0.15 1 123 654 32 5 46 (bottom view) (top view) rf spdt switch mmic
SPM3215 no.7265-2/3 isolation -- frequency insertion loss -- frequency 0.3 0.4 0.5 0.6 0.7 1.2 0.8 0.9 1.0 1.1 0 0.5 1.0 1.5 2.0 2.5 3.0 0 5 10 15 20 25 30 0 0.5 1.0 1.5 2.0 2.5 3.0 it04421 it04423 0 5 10 15 20 25 30 0 0.5 1.0 1.5 2.0 2.5 3.0 it04424 0v [in-out1] 3v [in-out1] isolation -- frequency 0v [in-out2] insertion loss -- frequency 0.3 0.4 0.5 0.6 0.7 1.2 0.8 0.9 1.0 1.1 0 0.5 1.0 1.5 2.0 2.5 3.0 it04422 3v [in-out2] isolation -- db frequency, f -- ghz insertion loss -- db frequency, f -- ghz isolation -- db frequency, f -- ghz insertion loss -- db frequency, f -- ghz continued from preceding page. rating parameter conditions min typ max unit f=800mhz 20 23 db in - - out1 f=1.5ghz 14 17 db f=2ghz 12 15 db isolation f=2.5ghz 10 13 db f=800mhz 22 25 db in - - out2 f=1.5ghz 16 19 db f=2ghz 14 17 db f=2.5ghz 12 15 db vswr in - - out1, in - - out2 f=1ghz to 2.5ghz 1.2 1.6 switching time in - - out1, in - - out2 f=1ghz to 2.5ghz 10 100 ns p in 1db in - - out1 f=1ghz to 2.5ghz 22 26 dbm in - - out2 f=1ghz to 2.5ghz 24 28 dbm application circuit ctl in out2 out1 c1 : 33pf at 0.8 to 1.5ghz 10pf at 1.9 to 2.5ghz v dd =3v r r : 10k c2 : 100pf c2 c1 c1 c1 1 2 3 6 5 4
SPM3215 no.7265-3/3 specifications of any and all sanyo products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. to verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. sanyo electric co., ltd. strives to supply high-quality high-reliability products. however, any and all semiconductor products fail with some probability. it is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. when designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. in the event that any or all sanyo products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of sanyo electric co. , ltd. any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. when designing equipment, refer to the "delivery specification" for the sanyo product that you intend to use. information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. sanyo believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. this catalog provides information as of october, 2002. specifications and information herein are subject to change without notice. ps output power -- input power 0 5 10 15 20 25 30 0 5 10 15 20 25 35 30 it04425 0v, f=1.0 to 2.5ghz output power -- input power 0 5 10 15 20 25 30 0 5 10 15 20 25 35 30 it04426 [in-out1] [in-out2] 3v, f=1.0 to 2.5ghz output power -- dbm input power -- dbm output power -- dbm input power -- dbm
|
